This page sets out the technical specification of Custom Pipe Over-Beam Device, HVAC Duct Crossing Beam Connector for Fresh Air Ventilation System as supplied by GUANDE, together with the selection rules that determine which variant suits a given project. It is written for specifiers, estimators and contractors who need to confirm a size, a material build-up and a connection method without waiting on a quotation.
| Item | Specification |
|---|---|
| Available Sizes / Models | Customized size; round duct interface / flat duct interface; custom configurations supported |
| Description | Customizable width, height, length and duct diameter; designed to cross structural beams while maintaining airflow passage; compatible with flexible ducts, circular ducts and flat ventilation pipes; both ends can be designed as round connectors or flat connectors; supports non-standard sizes, special angles and limited |
| Material / Construction | Galvanized steel / stainless steel / aluminized zinc steel optional |
A custom duct over-beam device that carries air past a structural beam or obstruction without dropping the ceiling. Width, height, length and duct diameter are all made to order, and both ends can be configured as round or flat connectors to match the adjoining ductwork. It also copes with non-standard angles and tight spaces.
Duct runs installed in a real building are never perfectly straight, and fittings have to absorb that. Products with a degree of angular tolerance and axial movement capability perform far better on site than rigid alternatives, because the connection itself is not required to act as a structural element. This matters most at the transition between a rigid plant connection and a flexible run, where thermal and vibration movement must be accommodated without opening a joint.
Different duct profile systems are not interchangeable, and an adapter between two systems is always a compromise. It adds a leak path, increases pressure loss and introduces a joint that may be the only one on the run without the benefit of the original sealing geometry. Standardising on a single profile family across a project is the simplest way to avoid the problem entirely. Where a transition is unavoidable, use a purpose-made adapter rather than forcing two incompatible components together.
Where a duct passes through a fire-rated compartment, the fitting used at that penetration is a fire-stopping component subject to building regulation. The correct approach depends on the rating of the wall or floor, the duct material and whether the duct is required to maintain the compartmentation itself. This is one of the few areas where a cost-driven substitution at purchase stage can create a compliance problem that is expensive to correct later. Confirm the requirement before ordering.
Quality inspection at GUANDE is not a final gate — it runs through the whole process. Incoming raw material is checked against specification before it enters production. In-process checks monitor dimensions and surface finish at defined intervals during the run. Finished Custom Pipe Over-Beam Device, HVAC Duct Crossing Beam Connector for Fresh Air Ventilation System are inspected against the approved sample, and a batch record is kept against every shipment so that any issue can be traced back to its production parameters.
Our plant runs scheduled production for Custom Pipe Over-Beam Device, HVAC Duct Crossing Beam Connector for Fresh Air Ventilation System with typical lead times of 15 to 25 days for standard items and 25 to 40 days for custom tooling projects. We load mixed containers directly at the factory, which lets us combine several product lines from your ventilation schedule into one shipment and reduce freight cost per unit. Confirmed lead times are stated on the order acknowledgement, not estimated at enquiry.
Use the following rules when converting a project drawing into an order. They reflect how the product performs in branch take-offs, direction changes and system terminations, where the practical limits are usually set by sealing quality, bend radius and connection tolerance rather than by the headline dimension.
Size the run from the design air flow and the acceptable pressure drop, not from the fan spigot. Undersizing a duct fittings run is the most common specification error and it cannot be corrected later without re-opening the ceiling.
Where the run passes through an unconditioned space, condensation risk — not mechanical strength — normally decides the specification. In those locations the insulated variant is the correct default and a bare equivalent is a false economy.
Keep one connector family for the whole run. Every change of system introduces an adapter, and every adapter is an additional leak path and pressure loss point.
Works with flexible duct, circular duct and flat ventilation pipes. For the PVC equivalent see our PVC over-beam fresh air duct connector.
GUANDE manufactures Custom Pipe Over-Beam Device, HVAC Duct Crossing Beam Connector for Fresh Air Ventilation System at our factory in Dezhou, Shandong, China, and ships direct to HVAC contractors, distributors and project specifiers worldwide. Wholesale, OEM and ODM programmes are welcome. Items are supplied in export cartons with the size and quantity marked on the outer label. For OEM programmes we can apply your own artwork and labelling subject to a minimum order quantity.
The products below are routinely specified alongside the item discussed in this guide. GUANDE manufactures the full range in our own plant for consolidated shipping:
Q: Can both ends be different types?
A: Yes, each end can be designed as a round connector or a flat connector.
Q: Do you make non-standard angles?
A: Yes, non-standard sizes, special angles and limited-space installations are all supported.
Q: Which materials are available?
A: Galvanised steel, stainless steel or aluminised zinc steel.
The southeast corner of the private entrepreneurship park in Huadian Town, Qihui County, Dezhou City, Shandong Province